Produkty dla flr mr176 (6)

Messer passend für Pfaff-Nähmaschinen

The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization. Specific torque [Nm/bar]:1,19 Operating pressure [bar]:200 Nominal torque [Nm]:238 Swivelling angle [ degrees° ]:250 Shaft end: (P) toothed shaft (Z) keyway key:P

The SAE J1939 standard (Serial Control and Communications Heavy Duity Vehicle Network) has originally been designed by SAE International to be used in heavy duty vehicles. In the meantime, the protocol is widely used also in agricultural machinery, rail vehicles and sea vessels and in a wide range of diesel-driven machinery. Target group J1939 training The target group of the J1939 intensive workshop is development engineers who are looking for a quick start into handling the communications profile or would like to get an insight into the J1939 protocol stack. Also, we address decision makers and product managers to enable them to assess the suitability of the J1939 protocol stack for their applications.

The output shaft of the HSH swivel motors has radial and axial hydrostatic bearings. Here, radially and axially arranged bearing pockets are supplied with pressurized oil via a separate pressure connection. As a result, the output shaft is centered radially and axially between liquid cushions and all metallic contact surfaces are permanently separated from each other by a thin liquid film. This eliminates wear caused by metallic friction in any operating state, even at zero speed compared to hydrodynamic plain bearings. In conjunction with highly dynamic control valves and angle of rotation sensors, these actuators are preferably used in controlled systems in which disturbance variables such as friction and the stick-slip effect must be reduced to a minimum. Furthermore, due to the lack of internal seals, they are ideal for test series with large numbers of load cycles where an interruption, e.g. due to the replacement of internal seals, is not permitted. Specific torque [Nm/bar]:2,05 Operating pressure [bar]:280 Nominal torque [Nm]:574 Swivelling angle [ degrees° ]:120

The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization. Specific torque [Nm/bar]:1,19 Operating pressure [bar]:200 Nominal torque [Nm]:238 Swivelling angle [ degrees° ]:250 Shaft end: (P) toothed shaft (Z) keyway key:Z

The output shaft of the HSH swivel motors has radial and axial hydrostatic bearings. Here, radially and axially arranged bearing pockets are supplied with pressurized oil via a separate pressure connection. As a result, the output shaft is centered radially and axially between liquid cushions and all metallic contact surfaces are permanently separated from each other by a thin liquid film. This eliminates wear caused by metallic friction in any operating state, even at zero speed compared to hydrodynamic plain bearings. In conjunction with highly dynamic control valves and angle of rotation sensors, these actuators are preferably used in controlled systems in which disturbance variables such as friction and the stick-slip effect must be reduced to a minimum. Furthermore, due to the lack of internal seals, they are ideal for test series with large numbers of load cycles where an interruption, e.g. due to the replacement of internal seals, is not permitted. Specific torque [Nm/bar]:32,80 Operating pressure [bar]:280 Nominal torque [Nm]:9184 Swivelling angle [ degrees° ]:120